Back

Chapter 25 and 26

Electric Potential of a Point Charge:

The discussion of electric potential is important because we are always looking for convenient sources of energy.  Since any two point charges exert a force of attraction or repulsion on each other, if one charge moves in the field of the other a distance dr  under an average force F, the work done is equal to Fdr.  This means that if there is just a single charge alone in the entire space, there is potential.  When a second charge is placed in the field of the first charge, then work and energy actualize and we think of potential energy.  Recall the "potential energy" concept you learned in Physics I.  The cause of gravitational potential energy is gravity.  The potential energy a rock has in the gravitational field of the Earth is because of gravity.  Gravity attracts mass M with a force F = Mg.  When a rock is lifted to a height h, the work done on it is equivalent to Mgh.  The potential energy stored or consumed is also Mgh. 

A similar concept applies to the electrostatic field that charge +q1 creates at a distance r1 from it:  E = kq1/r2.   If another charge +q2 is placed at r1q1 repels it.  As q2 moves away under the varying and repelling force F=kq1q2/r2 to , more and more work will be done on it.  The maximum amount of work that can be done may be calculated by integrating Fdr from r1 to .

The electric potential  V of a point charge q1 at a typical point P in space at a distance r1  from it is given by :

Now if another charge like q2  is placed at P a distance  r1 from  q1 , then  q2  finds a potential energy equal to

Consequently, we can write :                                 P.E. =  V1 q2     or, in general,     Ue =  V q

If we examine the unit of V, we will see that it has units of (energy per charge) or in SI units (Joules / Coulomb).  Let's do this examination.  Also let [  ] denote "the unit of ".

(Joule / Coul )  is called ( Volt ).  1 Volt means (1 J/Coul. )

A charge in space generates different Potentials at different distances from it.  The presence of a second charge is necessary for Potential Energy to make sense.

Example 1: Calculate the electric potential of q1 = 25.0nC at (a) 1.00m, (b) 2.00m, and (c) infinite long distance from it.

Solution: (a)  V1 = kq1 / r1 =  (9.00x109)(25.0x10-9) / (1.00) = 225 J /Coul. or  225 Volts.

                 (b)  V2 = kq1 / r2 (9.00x109)(25.0x10-9) / (2.00) = 113 J /Coul. or  113 Volts.

                 (c)  V3 = kq1 / r3 (9.00x109)(25.0x10-9) / ( ) = 

Example 2:  Calculate the potential energy that another charge q2 = 5.00nC possess when placed at the three different points of the previous example.

Solution:  P.E.1 = V1(q2) = 225(J/Coul.) * (5.00x10-9 Coul.) = 1130 nJ

This means that it takes 1130 nJ of energy to push a 5.00-nC of positive charge from infinity to a distance of 1.00m from charge q1.

                P.E.2 = V2(q2) = 113(J/Coul.) * (5.00x10-9 Coul.) = 565 nJ

             It takes 565 nJ to push a 5.00-nC charge from infinity to a distance of 2.00m from q.

                P.E.3 =  V3(q3)  =  (0.0) * (5.00x10-9 Coul.)  =  0.0 nJ.

This means that it takes no effort (energy) to place a charge very far away from q1.

Example 3:  How much energy is needed to place 1.00-μCof charge at each corner of an equilateral triangle 0.250m on each side?  Suppose that each charge is coming from far away (infinity) and that the triangle is in space far away from other electric charges.

Solution:  1. Placing the 1st charge does not require any energy because other corners are empty.   There is no  repelling force against the first charge and it can be done effortlessly (W1 = 0).   2. To bring a 2nd charge from infinity and place it at 0.250m from the 1st charge some work must be done.  The work to be done is equal to the change in P.E. of the 2nd charge in the field of the 1st charge.  It is equal to:

 

 W1 = 0.

 W2 = kq1q2 / r = [ (9.00x109)(1.00x10-6)(1.00x10-6) / (0.250)  ] J  = 36.0 mJ

 3. The 3rd charge faces resistance from both the 1st charge and the 2nd charge.

 W3  = {kq1 q3 / (0.250)} + {kq2 q3 / (0.250)} = 36.0 mJ +36.0 mJ  =  72.0 mJ

 Finally,  Wtotal  =   W1 +W2 +W3   = {36.+72.0} mJ   = +108.0 mJ

 

Potential in a Constant Electric Field:

A constant electric field is the field in between two parallel sheets equally but oppositely charged.  If the positive sheet is on the left and the negative on the right, as shown, the direction of E is to the right or along the (+x) axis.  Since E is constant, so is F, the force on any point charge q placed in E.  The Work done on +q by constant F as it is pushed to the right varies linearly with x, simply

W = F x

Since F = qE, the work done becomes:   

W = qE x  =  qEx      (2)  (Dot vanishes because Force and displacement are parallel).

As the field does more work in pushing q to the right, more of its potential is used up.  As the work done by the field (W) increases because of the increase in x, the P.E. or Ue of  q decreases.

We may write: W = - P.E.  = -Ue.    Equation (2) becomes:

-Ue = qEx    or,    (Ue /q) = -Ex     (3)

The left side is energy per unit charge or potential, V.  Equation (3) becomes:

V = -Ex

V is a linear function of x when E is constant.  At x=0, potential V is maximum and equal to Ex1. Why?  At x = x1, potential is zero. Why?  This makes the V equation to be

 V = -E(x-x1)

Equipotentials:

Around a charge distribution, there are points at which potential is the same.  This means that if charge q is placed at any of such points, it will have the same potential energy.  A collection of such points form a surface that is called an "equipotential surface."  In 2-D, we show such surfaces as lines and call them "equipotential lines."  For example, around a positive or a negative point charge, there are infinite concentric spheres that each is an equipotential surface.  Of course, the charge itself is at the center of such spheres.  In the 2-D drawings shown below, for each of the (+) or (-) charge, the concentric circles are in fact concentric spheres.

The above charges are of course assumed to be separate and very far from each other and any other charges.  

The important point is that anywhere a field line (red or blue) crosses an equipotential line (each black circle), the angle is 90 degrees; in other words, field lines are necessarily perpendicular the equipotential lines.  In Lab, it is easy to find the equipotential lines for a certain charge distribution by using a voltmeter.  Field lines can then be drawn keeping in mind that they must be at right angles to the equipotential lines.  Below, the field and eqipotential lines are shown for an electric dipole and a parallel-plates capacitor.

Field and Equipotential Lines of a Dipole

 

 

Field and Equipotential Lines in between the plates of a capacitor

As long as a charge like q2 travels on one equipotential surface (caused by another charge like q1) , its energy remains constant.  When q2 travels from one equipotential surface to another one, its energy changes.  The change in energy is equal to the work done on the charge that can be positive or negative.  The path that q2 takes in going from one equipotential surfcae to another, is not important.  What is important is the potential  difference between the two equipotentials.  In the following figure, two of the infinite equipotentials around charge q1 are shown.  The energy change that q2 experiences as it goes from equipotential 1 to equipotential 2 is the same regardless of the path taken.

Test Yourself 1:      click here

1) The electric field strength E1 of a point charge q1 at a distance r is (a) E1 = kq1/r2   (b) E1 = kq1/r   (c)  E1 = kq1/r3.

2) The electric force F of field E1on charge q2 is (a) F = E1q2     (b) F = {kq1/r2}q2     (c)  both a & b.      click here

3) The electric potential V1 of a point charge q1 at a distance r is (a) V1 = -kq1/r  (b) V1 = kq1/r2  (c)  V1 = kq1/r3.

4) The potential energy P.E. of point charge q2  at points in space where the potential is V1 is  (a) P.E. =V1 q2       (b) P.E. = (kq1/r) q2     (c) P.E. =  kq1q2 /r    (d) a, b, and c.      click here

5) The first 4 questions and their correct answers apply to point charges  (a) True   (b) False.

6) The force-field formula F = Eq is true (a) if E is caused by a point charge (b) if E is uniform and caused by a parallel-plates capacitor (c) both a and b.

7) The definition of the electric potential, V, at a point is (a) K.E. per unit charge at that point  (b) Force per unit charge at that point  (c) Electric P.E. per unit charge at that point     click here

8) The definition of the electric field, E at a point is (a) E = force per distance at that point  (b) E = force per unit charge at that point (c)  E = kinetic energy per unit charge at that point.      click here

9) The electric potential energy, P.E. is (a) P.E. =  Vq   (b) P.E. = Vq22  (c)  P.E. = (K.E.)q2.

10 ) The reason for using q2 in the above questions instead of just q is that (a) q2 is the charge that is placed in the field of q1 (b) the potential, V,  field, E, and force, F, in the above formulas are caused by charge q1  (c) both a & b.

11) Even if we do not use q2 instead of simply q, and write F = Eq and P.E. = Vq,  it is understood that (a) E and V are caused by a charge other than q  (b) q is placed in the field E of a different charge (c) both a & b.

12) The Metric unit of E, the electric filed, is (a) C/m  (b) N/C  (c) N/m.       click here

13) The Metric unit of V, the electric potential, is (a) C/s  (b) Joules/C  (c) Joules/m. 

14) The potential ,V, at 9.0m from a +25μCoul. charge is (a) 2778 J/C  (b) 25000 J/C   (c) 0.

15) If  +1.0Coul. of charge is placed at 9.0m from the charge in Question 14, it finds a potential energy of (a) 2778J  (b) 0   (c) 25000J.      click here

16) If  -1.0Coul. of charge is placed at 9.0m from the charge in Question 14, it finds an energy of (a) +2778J  (b) 0   (c) - 25000J.

17) The reason why the answer in Question 16 is negative is that (a) work has to be done to move the negative charge to infinity under the attraction of the positive charge (b) in moving the negative charge away, displacement is outward while the attraction force is inward  (c) both a & b.      click here

18) The potential at 3.0m from a -15.0μC charge is (a) -45000J/C  (b) 15000J/C  (c) 45000J/C

19) If 40.0μC of charge is placed at 3.0m from the charge in Question 18, it finds a potential energy of (a) -4.5J.  (b) -1.8J.  (c) 9.0J.

20) If -40.0μC of charge is placed at 3.0m from the charge in Question 18, it finds a potential energy of (a) -4.5J.  (b) -1.8J.  (c) 1.8J.      click here

21) The energy it takes to place a 4.0μC charge at a corner of an equilateral triangle (2.0m long on each side) that has no charge on it and is far from other charges is (a) zero   (b) 2.0J  (c)  -2.0J.

22) If in Question 21, if one corner has that 4.0μC charge, the energy it takes to place another 4.0μC charge at a 2nd corner is  (a) -0.144J  (b) 0.072J  (c)  0.144J.      click here

23)  In Question 22, to place another 4.0μC charge at the 3rd corner, it takes (a) 0.144J    (b) -0.072J    (c) 0.072J

24)  Formulas  V1 = kq1/r  and  P.E. =  kq1q2 /r  apply (a) to point charges only  (b) surface charges only  (c) both a & b.

25) In the space between a parallel-plates capacitor, electric field, E is constant.  Potential energy varies with distance from each plate.  The way P.E. varies with (x), its distance from one of the plates, in a constant E is (a) proportional to x  (b) proportional to 1/x  (c)  proportional to x2.      click here

 

Parallel-Plates Capacitor: 

Two parallel and metallic plates separated by an insulator form a capacitor that can store electric energy.  If two flat sheets of aluminum foil sandwich a thin sheet of paper, a capacitor is formed.  When aluminum foils are connected to the poles of a battery, electrons from the negative pole flow through the connecting wire and distribute themselves over one foil making it negative.  This negative side repels equal number of electrons from the other side and causes the other side to become positive.  The repelled electrons flow toward the positive pole of the battery where they get absorbed by it.  This process causes the battery to find new poles: the plates of the capacitor.  One difference is that the new poles have more charges accumulated on them.  The closer the plates (or the thinner the insulating material, here the paper), the more charge accumulation occurs on them.  However, there is a limit to the amount of positive and equally negative charges that can accumulate themselves on the two plates.  If accumulation exceeds a certain value, electric discharge takes place via a spark through the insulator.  The capacity of the plates is obviously dependent on the area of each plate.  Of course the assumption is that both plates are made equal and completely face each other.  The thinner the insulating material ( called the dielectric) the stronger the electric field between the plates and therefore the greater the capacity.  The Capacity of a parallel-plate capacitor is given by

  

 

In the above formula, A is the area of each plate and d is the gap between the plates or the dielectric thickness. The quantity ( ε ) is called the Permittivity of the material for electric field transmission through it.  The permittivity of vacuum (free space) is shown by ( εo ) .  These two quantities are related by  ( ε = κ εo ) where  κ  is called the dielectric constant of the material.  The value of  κ  for vacuum is 1, for mica is 5.4, and for water is 80.   This means that if mica is used as the insulator (the gap between the plates), the capacity increases by a factor of 5.4 compared to vacuum or almost air.

Example 4:  Calculate the capacity of a parallel-plates capacitor with rectangular (20.0cm by 30.0cm) aluminum plates separated by a 0.10mm sheet of paper.  The dielectric constant of regular paper is κ = 3.3.

Solution:

 

 

C = 3.3(8.85x10-12 (F/m) )* ( 0.200m X 0.300m) / ( 0.00010m) = 17.5x10-9 F = 17.5 nF

Note: 1 Farad of capacity is a very large capacity

 

Example 5:  Calculate the area of each plate of a 1.00-Farad parallel-plates capacitor with an air gap of 0.0500mm.

Solution:  Solving the capacity formula for (A), yields:   A = Cd /ε Substituting yields: 

                A = (1.00 F)(0.0500x10-3m) / (8.85x10-12 F/m) = 5.65x106 m2 

This means a square of side 2380m = 1.48 miles  ( A capacitor 1.48mi by 1.48mi ? Not practical !!!)

 

Charge-Voltage Formula:

For a capacitor, the charge on the capacitor, Q, and the voltage, V, it generates are related by the formula:

 

The capacity of a capacitor is 1F  if it can hold a maximum charge of  1C when connected to a voltage of 1V.  Majority of capacitors have very small capacities. Most of them are built to hold charges of μC or nC magnitudes.  Farad =  Coul. / Volt

Example 6:   Calculate the capacity of a capacitor that holds at most 30.0μC of charge when connected to a 12.0V battery.

Solution:  C = (Q/V) = (30.0μC / 12.0volts)    μC/volt       or        C = 2.50 μF.

 

Example 7:  When a capacitor is half charged, it has 60.0μC of charge on each plate and the voltage across it is 7.50 volts.  Find its capacity.

Solution:  The charge-voltage ratio is C = Q/V.  The more the accumulated charges, the greater the voltage it makes.  Capacity, C, is constant, anyway.  

C = (60.0μC) / ( 7.50 volts)  =   8.00μF  (micro-Farads).

 

Connection of Capacitors:

It is sometimes necessary to come up with a capacitor of a certain capacity that is not available in the lab.  By combining two or more of different capacitors, the desired capacity can be made.  In two ways capacitors may be connected:  in series and in parallel.  An equivalent capacity can be calculated for each type of connection.  The following figure shows both types of connection and a formula that calculates the equivalent capacity for each type of connection:

 

Fig. 1                                                        Fig. 2

  Series:

The battery voltage must be equal the sum of voltages across the three capacitors.  We may write:

 Vtotal  = Vab + Vbc + Vcd    (1)

 If 2 electrons flow to the left of C1, they repel 2 electrons from the right plate of C1 making its right plate positive.  Those repelled electrons move to the left side of C2 making it negative while repelling 2 electrons from the right side of it making its right side positive.  The same happens to C3.  The repelled 2 electrons from the right of C3 will be absorbed by the positive pole of the battery and the current is complete.  Of course saying "2 electrons" is just an example.  In reality some 1013 or 1014 more or less electrons might flow.  We end up with equal charges on capacitors that are in series.

Equivalent Capacity: The single capacitor that can replace those three capacitors must hold the same amount of charge, simply Q.  For the equivalent capacitor, we may write:

Q = CeqV from which V = Q / Ceq.

For each capacitor we may write its own charge-voltage relation. Vab = Q / C1 , Vbc = Q / C2  ,  Vcd = Q / C3Using (1), results in

  Q / Ceq  =  Q / C1  +  Q / C2   +  Q / C3

   Dividing through by Q, yields:

    1 / Ceq  =  1 / C1  +  1 / C2   +  1 / C3

  Parallel:

The total charge Qtotal  that leaves the battery distributes over the three capacitors such that

 Qtotal  = Q1 + Q2 + Q3.

 If capacities C1, C2, and C3 are proportional to numbers 2, 3, and 4, for example, and say 18 electrons leave the negative pole of the battery, 4 will flow to C1, 6 will flow to C2, and 8 will flow to C3 and settle on their left plates.  Equal number of electrons will be repelled from the right side plates making them positive.  The repelled 18 electrons will be absorbed by the positive pole of the battery and the current is complete.  This is just an example, in reality some 1013 or 1014 more or less electrons might flow.  Qtotal  = Q1 + Q2 + Q3.

Equivalent Capacity:

Using Q = CeqV for the equivalent capacitor as well as the individual capacitors, yields:

   CeqV  = C1V  +  C2V  +  C3V

Dividing through by V, yeilds:

       Ceq  = C1  +  C2  +  C3

Look at the following two simple examples:

 Example 8: A 30.0μF capacitor is in series with a 6.00μF capacitor.  Find the equivalent capacity.

Solution:

1 / Ceq  = 1 / C1 + 1 / C2 ;

1 / Ceq  = 1 / 30.0 + 1 / 6.00 ;  Ceq  = 5.00μF ;

 Make sure you use horizontal fraction bars when verifying the solution.

 

 

 

 Example 9: A 30.0μF capacitor is in parallel with a 6.00μC capacitor.  Find the equivalent capacity.

Solution: Ceq = C1 + C2  ;

 Ceq  = 30.0 + 6.00 ;

 Ceq  = 36.00μF

 

 

Example 10:  In the figure shown, find the equivalent capacity.

Solution:  Between a and b, there is a parallel set that simply add up.  Cab = 60.0μF

Then, Cab and Cbc are in series and their reciprocals add up to give the reciprocal of Cac.

  1 / Cac = 1/Cab + 1/Cbc = 1/60 + 1/20 = 1/15

      Cac =  15.0μF

 

Example 11:  In the figure shown, find the voltage across and the charge accumulated in each capacitor.

 

Solution:  From the top figure:

Cab = 12.0 + 15.0 = 27.0μ;  and from the bottom figure:

 1/Cac = 1/Cab + 1/Cbc  ;  1/Cac = 1/27 +1/13.5 ;

 Cac = 9.00μF.  This is the overall capacity that the 18.0-V battery faces.  Since Q = CV; thus ,

Q = (9.00μF)(18.0V)  = 162 μCoul.  This means that each capacitor in the bottom figure accumulates 162μC of charge (They are in series).   Knowing their capacities, we can calculate their voltages.

Qab = CabVab ; Vab = 6.00 Volts (Same for C1 & C2)

Qbc = CbcVbc  ;   Vbc =  12.0 Volts  (For C3)

Going to the ab-portion of the top figure, we may find how the two parallel capacitors divide the 162μC of charge.  They divide it as (12/27) and (15/27) proportions.  Go to the next column.

 

 Q1 = (12/27)(162μC ) = 72.C

 Q2 = (15/27)(162μC ) = 90.C.   Of course,

 Q3 = 162μC

 

Energy Stored in a Capacitor:

Note that the product QV has unit of energy.  Q is in Coul., and  V is in Joules/Coul..  The product QV has unit of Joule in (SI).  Keeping this in mind, let's calculate the energy stored in a capacitor that has charge Q on it causing a voltage V across it.

There are other versions of this formula.  Since Q = CV, we get Ue = (1/2)CV2.   Also,   Ue = (1/2)QV.

Example 12:  A 15μF-capacitor is connected to a 9.6-V battery.  Calculate (a) the charge accumulation and (b) the energy stored in it.

Solution:  (a)  Q = CV    ;    Q = (15μF)(9.6 V)  =  144μC

                (b)  Ue = (1/2)QV    ;    Ue = (1/2)(144μC )(9.6V) = 690 μJ

 

Test Yourself 2:

1) A capacitor is a device that stores (a) kinetic energy.  (b) electric energy.  (c) elastic potential energy.      click here

2) The capacity, C of a capacitor is proportional to (a) the area of one of its plates, A.  (b) the the reciprocal of the gap between its plates, (1/d).  (c) to the dielectric constant, κ of the the material between the plates.  (d) a, b, and c.

3) The dielectric constant, κ of the insulating material between the plates of a capacitor is (a) the ratio of the permittivity of that material, ε to the permittivity of vacuum, εo.  (b) such that we may write: ε = κεo.  (c) both a & b.      click here

4) The value of εo,  the permittivity of vacuum for the passage of the electric field effect, is (a) 8.85x10-12 Farad/meter.  (b) 8.85x10-12 Coul.2/(Nm2).  (c) 1/(4πk) where k is the Coulomb's constant.   (d) a, b. &c.      click here

5) Capacity is also defined as (a) the charge-to-voltage ratio of the capacitor.  (b) charge -to-distance ratio of a capacitor.  (c)  charge-to-energy ratio.      click here

6) When an empty capacitor is connected to a battery, the very first voltage across the capacitor is (a) zero.  (b) exactly equal to the battery voltage.  (c)  half of the battery voltage.

7) When an empty (deflated) basketball is connected to an air pump, the very first pressure in the basketball is (a) zero.  (b) equal to the pump's or the compressor's pressure.  (c) half of the compressor's pressure.

8) When the capacitor in Question 6, is half-charged, the voltage across it is (a) equal to the battery's voltage.   (b) equal to 1/2 of the battery's voltage.  (c) fluctuating.      click here

9) When the basketball in Question 7, is halfway filled, the air pressure in it is (a) equal to the pump's pressure.   (b) equal to 1/2 of the pump's pressure.  (c) fluctuating.

10) When the capacitor is fully charged after sufficient time has elapsed, the voltage across it (a) is equal to the battery's voltage.  (b) is zero because it does not accept any more charges.  (c) is neither a nor b.      click here

11) When the basketball in Question 7, is fully inflated to where the pump cannot inflate it anymore, the pressure in it (a) is equal to the pressure that the pump can generate.  (b) is zero because it does not accept any more air.  (c)  neither a nor b.

12) The above questions lead to (a) the proportionality of charge accumulation, Q on a capacitor's plate to the voltage developed, V across it.  (b) the fact that capacity C, is the proportionality constant.   (c) Q = CV .   (d) a, b, & c.

13) The voltage across a 12-μF capacitor is 5.0V.  Each of its plates has a charge of (a) 60.μCoul.  (b) 2.4μCoul.  (c) 0. 

14) The charge on and the voltage across a capacitor are 85μCoul. and 5.0 volts, respectively.  Its capacity is (a) 425μF.  (b) 425 Farad.  (c) 17μF.      click here

Problem:  Draw a battery and three parallel-plate capacitors connected to it in series as shown in Fig.1 above.  During the very first moments, suppose 5 trillion negative charges travel from the negative pole of the battery and distribute evenly over the nearest plate they can reach.

15)  What happens to the other plate of that capacitor? (a) It receives 5 trillion electrons.  (b) It loses 5 trillion electrons.  (c) It becomes 5 trillion protons positive.  (d) b & c.      click here

16) Where do the repelled electrons of the first capacitor go? (a) They jump into air.  (b) They go to the nearest plate of the middle capacitor and make it 5 trillion electrons negative.  (c) the return to the negative plate the same way they came in.

17) What happens to the opposite plate of the middle capacitor? (a) It becomes 5 trillion protons positive.  (b) It receives 5 trillion electrons.  (c) Neither a no b.      click here

18) Is it correct to say that the third capacitor experiences the same process as the middle on? (a) Yes.  (b) No.

19) What happens to the repelled electrons from the third capacitor? (a) They go to the positive pole of the battery and get absorbed by it.  (b) They complete the flow of electrons in the circuit.  (c) both a & b.      click here

20) If we name the capacitor's charges Q1, Q2, and Q3,  then (a) Q1= Q2= Q3.  (b) Q1= Q2+ Q3.  (c) neither a nor b.

21) We may say the capacitors in series accumulate the same amount of charge. (a) True.  (b) False.      click here

22) For capacitors C1 and C2  (knowing C1>C2) in series with a battery (a) Q1>Q2.  (b) Q1< Q2.  (c) Q1= Q2 .

23) For capacitors C1 and C2  (knowing C1>C2) in parallel with a battery (a) Q1>Q2.  (b) Q1< Q2.  (c) Q1= Q2.

24)  The total capacitance, Ceq for C1= 25.F and C2 = 5.00μF connected in parallel is (a) 4.25μF.  (b)30.0μF. (c) 125μF.

25) The total capacitance, Ceq for C1= 25.F and C2 = 5.00μF connected in series is (a) 4.17μF.  (b)30.0μF. (c) 125μF.

26) The total capacitance, Ceq for C1= 15μF and C2 = 52μF connected in series is (a) more than 67μF.  (b) less than 15μF.  (c) equal to 67μF.      click here

27)  Two capacitors C1= 8.0μF and C2 = 16μF are connected in parallel to a 4.0-V battery. The accumulated charges are: (a) 32μCoul. and 64μCoul.   (b) 2.0μCoul. and 4.0μCoul..  (c) neither a nor b.

28)  Two capacitors C1= 8.0μF and C2 = 24μF are connected in series to a 4.0-V battery. The accumulated charges are: (a) 32μCoul. and 96μCoul.   (b) 2.0μCoul. and 6.0μCoul..  (c) 24μCoul. and 24μCoul..      click here

29) The voltages across C1 and C2 above are (a) 3.0V and 1.0V.  (b) 4.0V and 4.0V.  (c) 24.0V and 24.0V .

30) The product QV has unit of  (a) force.  (b) power.  (c)  energy.      click here

31) When a capacitor is fully charged it can give back the accumulated charge, Q on it (a) as it keeps the same voltage V.  (b) as the voltage across it decreases with gradual charge loss.  (c) as the voltage across it increases with gradual charge loss.

32)  Based on the previous questions, the energy stored in a capacitor, Ue, is the product (a) QV.  (b) (1/2)QV.  (c) 2QV .

33) Because Q = CV, the stored energy,  Ue = 1/2QV may be written as (a) Ue = 1/2CV2. (b) Ue = 1/2Q2/C.  (c) both a & b.

34) The energy stored in a 60.0-μF-capacitor when the voltage across it is 5.00V is (a) 1500μJ.  (b) 3000μJ.  (c) 750μJ .

35) The charge accumulation on the capacitor of the previous problem is (a) 300.μCoul. .  (b)12.0μCoul. .  (c) 120μCoul. .

36) If you now use Ue = 1/2QV to calculate the energy again, you get  (a) 1500μJ.  (b) 3000μJ.  (c) 750μJ.       click here